The nominal value of the resistance of the valve for vehicles with engine GA16DE should be 10 ohms

* Check of the valve of adjustment of turns of idling, the fuel pressure and the relief valve * - Nissan: More Than Expected!
battery block bolt weight petrol inlet gas release switch sensor diesel engine fluid valve ring gear assembly housing body bridge motor pump piston hole wire drive unit start relay valve lever signal removal connection Connection gathering brake seal emphasis setting circuit cylinder hose connector Electrical
Timur otlichyany advice for lyub.voditeoley Ruslan: I should polasmasovy the history of the automobile cum chickpeas 38-5 35-5 width 25 ruslan: Hello I wanted to ask what size needle bearing gear 3rd gear and how much will be [...] Sam: Do not Starts the cold. Drizzle carp in Zafon started up. And all day norm. Well tupit still not [...] Nicholas: Intelligent. Sorry printed in reverse ... laewskij: In DMRV block for 4-pin, and used 3.
General description: Front bumper - removal and installation. Hood - fit. Rear bumper - removal and installation of doors - Removing and installing door trim, center console - removal and installation of the cabin side trim and flooring. Side mirrors. Rear-view mirror in the cabin. Front and rear seats
This valve is designed to keep the idle speed at a certain level. S action valve is actuated by a stepping motor and opens the air supply passage bypassing the throttle valve. Cars with engine GA16DE also have valve of stabilization of turns of idling, which is triggered when you turn on the air conditioner and power steering.
The nominal value of the resistance of the valve for vehicles with engine GA16DE should be 10 ohms at an air temperature the history of the automobile of 25 * C, while cars with engine QG180E and SR20DE - 20-24 ohms at an air temperature of 20 * C. Otherwise, replace with a new valve.
18 Turn on the ignition and ask the assistant the history of the automobile to listen to the stepper motor actuation control valve idle speed, which is accompanied by a distinctive sound. If the operating sound of the stepping motor can not be heard, check the integrity of the motor windings. If the coil is normal, it is probably a fault of the stepper motor speed controller the history of the automobile
3 Start the engine, make sure the seal and read the pressure gauge reading, the fuel pressure at idle with the reduction valve connected to the fuel rail pressure hose Low pressure should be 2.35 bar, and the detached - 2.94 bar. If it is not, check the pressure reducing valve (regulator) pressure in the fuel rail.
6 Start the engine and read the pressure the history of the automobile gauge on the fuel hose, changing the vacuum pressure supplied to the regulator. Fuel pressure should decrease with increasing dilution, otherwise replace the pressure reducing valve in the fuel rail.
See also: - Fuel Injection System - ... Self-checking the fuel injection system is practically impossible for the reason that this requires first of all the relevant instrumentation and ... - General description of the distributed system (multi-point) fuel injection consists of the intake manifold, fuel rail with injectors, throttle body, air filter and electronic components, ... - General description (continued) Location 1.0a electronic fuel injection system components in the engine compartment. Cars with petrol engines GA16DE 1 - pressure sensor liquid ... - Check encoder ... This sensor equipped vehicles with engines and QG18DE SR20DE. However, this sensor in the engine SR20DE not included in the ... - Check the valve shut-off ... In loop fuel injection system included 1 solenoid valve fuel cutoff (see. Illustration 2.0). To stop the engine, the history of the automobile it is necessary ...
Tags: inlet pressure, the engine, throttle, ignition, sound, Valve, air pressure gauge, pump failure, the drive, check, start-up, control, resistance tube, filter, hose, plug, electric
User manual maintenance of the engine cooling system, heating and ventilation system of injection of fuel - petrol the history of the automobile engines power supply system - diesel engines the history of the automobile exhaust system (exhaust) Fuel system Ignition system Clutch Manual the history of the automobile Transmission the history of the automobile Automatic Transmission Brakes Suspension and steering Body and Trim Electrical System Wiring the history of the automobile Diagrams
Ignition the history of the automobile timing - checking and adjustment - 3,147 views Nissan Primera the history of the automobile (P11) - 2,269 views Toothed belt drive Diesel injection pump - removal and installation the history of the automobile - 2065 views Check valve fuel cutoff, pedal and cable