BattleTag : CreatiVe # 2573 Intel Core 2 Duo E8400@3.00GHz 4.00 GB Dual-Channel DDR2 @ 533MHz Giga

Auto
Hello, today the machine stopped varti.Lampichkite lit and full laundry water, but unfortunately varti.Za warranty ended a few months ago and I can not zakaram.Ta my question is whether the problem is in the electronics and the engine is blown. Thanks in advance.
BattleTag : CreatiVe # 2573 Intel Core 2 Duo E8400@3.00GHz 4.00 GB Dual-Channel DDR2 @ 533MHz Gigabyte Technology Co., Ltd. EP35-DS3 ATI Radeon HD 5670 Philips 220SW (1680x1050 vin @ 60Hz) 244GB Hitachi Hitachi HDP725025GLA380 ATA Device MS Windows 7 Ultimate 64-bit SP1
I wrote in the title Gorenje WA62081.
BattleTag : CreatiVe # 2573 Intel Core 2 Duo E8400@3.00GHz 4.00 GB Dual-Channel DDR2 @ 533MHz Gigabyte Technology Co., Ltd. EP35-DS3 ATI Radeon HD 5670 Philips 220SW (1680x1050 @ 60Hz) 244GB Hitachi Hitachi HDP725025GLA380 ATA Device MS Windows 7 Ultimate 64-bit SP1
Posted: 14:09:12 - 12:54
BattleTag : CreatiVe # 2573 Intel Core 2 Duo E8400@3.00GHz 4.00 GB Dual-Channel DDR2 @ 533MHz Gigabyte Technology Co., Ltd. EP35-DS3 ATI Radeon HD 5670 Philips 220SW (1680x1050 @ 60Hz) 244GB Hitachi Hitachi HDP725025GLA380 vin ATA Device MS Windows 7 Ultimate 64-bit SP1
Group: Members Posts: 192 Joined: 06-August 12 Reputation: 20 Gender: Male City: Plovdiv
At first reading, can be seen starting capacitor, I guess that is one. Washing machines are not my specialty, so I give a guess. A few months old washing my mother did not rotate, or fill their water, etc., when replacing the condenser is fine.
There is one peculiarity, which does not mention any of opinion on the matter. vin The engine of the machine actually not one but two - housed in a casing. In this situation, one engine for the main wash and the other engine is spinning. Check that the machine centrifuge!, If centrifuged, then the problem is in the part of the engine wash. Rilken is right, that may be a condenser, and if the water filter is clogged. If the filter vin and condenser are in order, then you need to check the condition of the engine for the laundry. If you have an Ohmmeter, you can do the following: Hang the plug to the engine, which has a 6-pin. The engine has a 6-pin connector, as follows, from left to right: vin Top row: General - Centrifuge - Engine wash Bottom line: Engine wash-centrifuge - General Measure the resistance between Total (upper row) and Spin (upper row), we get about 7 ohms resistance, and between Total (upper row) and Spin (bottom center), you should get about 14 ohms resistance. Engine laundry, Total (bottom row) engine wash (top row) and total (bottom vin row) and Engine wash (bottom row), the measured value of the two, the difference shall not exceed one ohm. Active terminals to ground (housing washer) should not give indication. If there is no indication of the device under measurement between Total and active motor terminals - so the engine is blown.
There is one peculiarity, which does not mention any of opinion on the matter. The engine of the machine actually vin not one but two - housed in a casing. In this situation, one engine for the main wash and the other engine is spinning. Check that the machine centrifuge!, If centrifuged, then the problem is in the part of the engine wash. Rilken is right, that may be a condenser, and if the water filter is clogged. If the filter and condenser are in order, then you need to check the condition of the engine for the laundry. If you have an Ohmmeter, you can do the following: vin Hang the plug to the engine, which has a 6-pin. The engine has a 6-pin connector, as follows, from left to right: Top row: General - Centrifuge - Engine wash Bottom vin line: Engine wash-centrifuge - General Measure the resistance between Total (upper row) and Spin (upper row), we get about 7 ohms resistance, and between Total (upper row) and Spin (bottom center), you should get about 14 ohms resistance. Engine laundry, Total (bottom row) engine wash (top row) and total (bottom row) and Engine wash (bottom row), the measured value of the two, the difference shall not exceed one ohm. Active terminals to ground (housing washer) should not give indication. If there is no indication of the device under measurement between Total and active vin motor terminals - so the engine is blown. In fact I did not mention that the engine vin actually has two speeds - one for normal washing and the other for spin. Basing from the fact that when the program starts the machine vin at low speed, vin ie small engine speeds, but to swing it is necessary to have called. starting capacitor, which aims to change vin the size of the current one or more rotations of the electric vin motor in order to create a rotating magnetic vin field to compensate for drops in the rotation of the rotor. Release