Checking the tightness of connections check my reg injection system, adjustment of turns of idling and the maintenance WITH
car battery tank petrol unit weight bolt release gas pressure motor drive valve ring contact housing body mass point model bridge motor power pump rim volume drive axle bearing wire start radiator valve repair brake lever light converging focus setting filter cylinder chassis tire hose
Mercedes-Benz L4500A and L4500S - 541 views Carburetor SOLEX 4A-1 and adjustment of turns of idling and the maintenance WITH - 520 views halftrack artillery tractors - 483 hits three-ton trucks Mercedes - Benz L3000 and L3000S - 397 views Mercedes-Benz 170VK - 237 views
Adjusting the speed of the engine and warm the CO content in the exhaust gases of the engine warm (+6 rating, 2 votes) Coolant pump and thermostat housing (8-cylinder engine) (5 rating, 1 votes) Replacement of a cooling liquid (+5 rating, 1 votes ) Removing the distributor (5 rating, 1 votes) Check valve timing (+5 rating, 1 votes)
Disable the fuel pump relay and connect the terminals 7 and 8 with a piece of wire to create pressure in the fuel system. Check seals distributor plunger (2) by pushing check my reg the flap (4) air flow meter all the way down and hold it in this position. In the air line may be the appearance of the fuel, but only a small amount. Otherwise it is necessary to replace the washer distributor plunger. After checking the system for leaks all removed items set in place.
Check the tightness of the intake system. To do this with a brush to cover gasoline all joints of the inlet to the engine running. If the speed increase, it means that the engine sucks air in an increased amount just mashed place. Locate and repair the leaks.
Remove the protective cap (4) through a slot at the top of the air filter. check my reg In the absence of a special tool to pierce the plastic cap, insert a screw or self-tapping screw and remove the screw with seal. A small screwdriver to push down on the adjusting device (2) and slightly rotated to until the end of the hex (3) comes into contact with the bolt adjustment of CO (61) and adjust the CO content.
Give a partial check my reg load on the engine, including all electrical consumers check my reg (air conditioning, headlights, radio, etc.). The engine should run smoothly if it is not, then adjust the idle speed.
It has long been obsolete aircraft of the Second World excite the imagination to this day. Many of these aircraft are a significant step forward check my reg in the development of global aviation, others remain a monument of his time, retained the imprint of the terrible and bloody events of the brutal war in the air.
See also: - Carburetor SOLEX 4A-1 and adjustment ... Carburetor Solex carburetor is a two-chamber, which consists of 4 screws connected with each other major ... - Troubleshooting ... Having trouble in receipt of the fuel system check my reg should be checked as follows: Check if there fuel ... - Air Filter - Removal and ... Removal Remove the rubber check my reg tube (2) to the inlet of the carburettor by loosening the clamp is preliminary. Unscrew the 3 fastening ... - Adjust the speed of the warm ... Connect the tachometer and CO meter in accordance with the instruction manual. Warm up the engine to operating temperature. Temperature ... - Checking and adjusting valve ... Check and adjust valve meter of air at high throttle position meter engine will not start. check my reg ...
Tags: petrol, bolt, weight, injection, inlet gas engine, start, tools, housing, air conditioning, point, bridge, pump speed, pedal, plug, appliance, wire, start-up, distributor, fuel, adjustment, check my reg control, relay light compounds converge, focus, filter, cylinder, hose, electric
Identification of the vehicle engine ignition system maintenance tasks ignition system Lubrication System Cooling System Service Cooling System Fuel System Fuel Injection System Clutch gearboxes (PPC) Propeller shaft Front suspension Rear suspension Steering Maintenance Steering
We recommend:
car battery tank petrol unit weight bolt release gas pressure motor drive valve ring contact housing body mass point model bridge motor power pump rim volume drive axle bearing wire start radiator valve repair brake lever light converging focus setting filter cylinder chassis tire hose
Mercedes-Benz L4500A and L4500S - 541 views Carburetor SOLEX 4A-1 and adjustment of turns of idling and the maintenance WITH - 520 views halftrack artillery tractors - 483 hits three-ton trucks Mercedes - Benz L3000 and L3000S - 397 views Mercedes-Benz 170VK - 237 views
Adjusting the speed of the engine and warm the CO content in the exhaust gases of the engine warm (+6 rating, 2 votes) Coolant pump and thermostat housing (8-cylinder engine) (5 rating, 1 votes) Replacement of a cooling liquid (+5 rating, 1 votes ) Removing the distributor (5 rating, 1 votes) Check valve timing (+5 rating, 1 votes)
Disable the fuel pump relay and connect the terminals 7 and 8 with a piece of wire to create pressure in the fuel system. Check seals distributor plunger (2) by pushing check my reg the flap (4) air flow meter all the way down and hold it in this position. In the air line may be the appearance of the fuel, but only a small amount. Otherwise it is necessary to replace the washer distributor plunger. After checking the system for leaks all removed items set in place.
Check the tightness of the intake system. To do this with a brush to cover gasoline all joints of the inlet to the engine running. If the speed increase, it means that the engine sucks air in an increased amount just mashed place. Locate and repair the leaks.
Remove the protective cap (4) through a slot at the top of the air filter. check my reg In the absence of a special tool to pierce the plastic cap, insert a screw or self-tapping screw and remove the screw with seal. A small screwdriver to push down on the adjusting device (2) and slightly rotated to until the end of the hex (3) comes into contact with the bolt adjustment of CO (61) and adjust the CO content.
Give a partial check my reg load on the engine, including all electrical consumers check my reg (air conditioning, headlights, radio, etc.). The engine should run smoothly if it is not, then adjust the idle speed.
It has long been obsolete aircraft of the Second World excite the imagination to this day. Many of these aircraft are a significant step forward check my reg in the development of global aviation, others remain a monument of his time, retained the imprint of the terrible and bloody events of the brutal war in the air.
See also: - Carburetor SOLEX 4A-1 and adjustment ... Carburetor Solex carburetor is a two-chamber, which consists of 4 screws connected with each other major ... - Troubleshooting ... Having trouble in receipt of the fuel system check my reg should be checked as follows: Check if there fuel ... - Air Filter - Removal and ... Removal Remove the rubber check my reg tube (2) to the inlet of the carburettor by loosening the clamp is preliminary. Unscrew the 3 fastening ... - Adjust the speed of the warm ... Connect the tachometer and CO meter in accordance with the instruction manual. Warm up the engine to operating temperature. Temperature ... - Checking and adjusting valve ... Check and adjust valve meter of air at high throttle position meter engine will not start. check my reg ...
Tags: petrol, bolt, weight, injection, inlet gas engine, start, tools, housing, air conditioning, point, bridge, pump speed, pedal, plug, appliance, wire, start-up, distributor, fuel, adjustment, check my reg control, relay light compounds converge, focus, filter, cylinder, hose, electric
Identification of the vehicle engine ignition system maintenance tasks ignition system Lubrication System Cooling System Service Cooling System Fuel System Fuel Injection System Clutch gearboxes (PPC) Propeller shaft Front suspension Rear suspension Steering Maintenance Steering
We recommend:
No comments:
Post a Comment